ตำแหน่ง QC Engineer and Welding Inspector

บริษัท Plant (Module) Co., Ltd.

ที่อยู่บริษัท Chonburi Thailand

เงินเดือน สำหรับสมาชิกเท่านั้น

ลักษณะงานที่ทำ
- Reviewed construction plans, specification, and drawings.
- Assist with obtaining permits and other necessary documentation.
- Prepare and reviewed pWPS / WPS / PQR / WQT, Reviewed NDE Procedure / Method statement to comply with ITP, project specifications and code standards.
- Inspection material received such as appearance, dimension, mill certificate including test sampling cutting to comply with project specifications requirements.
- Perform welder qualification test and issue welding certificate and card test.
- Monitor construction activities for compliance with plans and specifications.
- Prepare and maintain progress reports and documentation.
- Coordinate with contractors and suppliers.
- Record any conformances in work to ensure disposition of non-conformances in accordance with project requirement.
- Issue report to the QA/QC Manager and pursue non-conformances and any other deficiencies requiring corrective actions.
- Review and approve QC documentation for completion testing and handover of work packs, systems or parts of the plan.
- Maintain register of all QA/QC documentation requiring foe work on site and ensure documents in use by site personal are correct issue.
- Reviewed shop drawing and preparation running joint in weld-map.
- Perform inspection welding consumable storage.
- Perform Fit-up inspection such as joint preparation, alignment and dimension, tack weld to comply specification and drawing.
- Monitored during weld perform inspection welder, tack welder, registers welding surveillance to comply WPS.
- Visual inspection, after weld finish perform inspection weld appearance, surface condition to be free form defect.
- Dimension inspection after weld finish, tolerances to be comply drawing.
- Select joint NDE and submit to issue NDE request.
- Monitor NDE process to process comply with procedure and verify joint correct with NDE request.
- Internal final inspection before issue IRV to contractor.
- Reviewed Fit-up report, Visual report, Welding history sheet and NDE Report are correct.
- Final inspection with contractor and review document release to panting process.
Application code: AWS D.1.1 / D1.2 /ASME Sec IX
Material Type: S235 JR / S275 JR / S355MLO / API2W Gr.50 / API 5L X52QO PSL2 / ASTM A106 Gr. B
/ API2W Gr.50 / API 5L X52 / ASTM A53 Gr. B

ตำแหน่ง Welding Inspector

บริษัท Zeniya Thailand CO., LTD.

ที่อยู่บริษัท Chonburi Thailand

เงินเดือน สำหรับสมาชิกเท่านั้น

ลักษณะงานที่ทำ
- Reviewed WPS / PQR / WQT / NDE Procedure / Method statement to comply with ITP,
project specifications and code standards.
- Inspection material such as appearance, dimension received to comply with project specifications requirements.
- Witnessed welder qualification test.
- Inspection welding consumable storage.
- Fit-up inspection, check joint preparation, check dimension to comply with drawing.
- Check welder, tack welder registers and check welding consumable to use.
- Monitored during weld, perform check welding surveillance to comply WPS.
- Visual inspection, after weld finish.
- Witness dimension checked after weld finish.
- Reviewed fit-up and visual report.
- Reviewed NDE request.
- Witnessed NDE inspection process.
- Witnessed process leak test.
- Reviewed NDE inspection test report, dimension test report and leak test report.
- Final inspection before release to paint.
- Reviewed welding history sheet.
- Weekly progress report to section manager.
- Reviewed documentation and all inspection report & traceability MDR.
Application code: AWS D.1.1 / D1.2 /ASME Sec IX / JIS
Material Type: STK400 / SS400 / SUS316L / Aluminum Alloy A5052P-H112

ตำแหน่ง Welding Inspector and NDT Coordinator

บริษัท BJC Heavy Industry PLC.

ที่อยู่บริษัท Rayong Thailand

เงินเดือน สำหรับสมาชิกเท่านั้น

ลักษณะงานที่ทำ
- Reviewed ITP / WPS / PQR / WQT / NDE Procedure / Method statement to comply with ITP, project specifications and code standards.
- Reviewed shop drawing and weld-map included preparation and rectification.
- Fit-up inspection, check joint preparation, check dimension to comply with drawing.
- Witnessed dimension checked before weld.
- Check welder, tack welder registers and check welding consumable.
- Monitoring during weld, perform check welding surveillance to comply WPS.
- Visual inspection, after weld finish.
- Prepare and reviewed fit-up and visual report.
- Identify weld joint to issued NDE request to third party.
- Witnessed NDE inspection process.
- Reviewed NDE inspection test report, dimension test report and weld history sheet.
- Monitored percent reject late of the welder and analyze the root cause of imperfections to rectification case UT rejected.
- Witnessed before bolt torque tightening process.
- Monitored status and activities of process quality of steel structure such as fit-up, weld date, visual, NDE dimension, bolt torque tightening, punch list to complete process.
- Weekly progress report to supervisor and main contractor.
- Support QA to rectification and close NCR case.
- Walk down inspection with main contractor and third party to record point unfinished works and issued internal punch list
- Informed punch list to production to be rectified and monitored punch list cleared and closed status in system.
- Gather and prepared document inspection completed process and issued release to paint.
- Pre shipment inspection and issued release module according shipment.
- Line checks piping and clearing closed master punch lists before leak test.
- Flange management. Check flange face and measurement alignment flange before bolt torque tightening.
Application code: AWS D.1.1 / EN1090 / ASME B31.1 / ASME B31.3 / ASME Sec. IX
Material Type: S355JR / SM490YA / SS400 / S275JR / A325MSG / A1101 / SA106 Gr B / SA335 Gr P22, P91 / SA312 TP304, 316

ประสบการณ์ทำงานอื่นๆ
IS Industry Thailand
September 2013 to March 2021
Position: NDT Supervisor
Duties:
- Prepared NDT procedure and method statement submit to client.
- Prepared scan plan and plan schedule to perform to inspection submit to client.
- Demonstration NDT technique to use inspection and qualify performance NDT personal with client.
- Discuss and clear scope of job with client.
- Recommended NDT method to appropriate with condition of work piece to client.
- Explain scope of job with team staff and plan to work on site.
- Observation and coordinate with team to rectification any problems occurrence duration inspection.
- Perform NDT inspection on site method MT, PT, UT, UTM, VT, PAUT, TOFD, and PMI, type of work piping, pressure vessel, fire heater, steel structure, mechanical part.
- Interpretation of result NDT inspection to analyze and decide accept or reject comply with code standard requirement.
- Prepare and reviewed report NDE test before submit to client.
- Monitored equipment machine calibration or certificate expiry and contract or submit to renewal certificate.
- Control document rerated below accordance ISO 9001 standard.
Application code: ASME Sec I, ASME Sec V, ASME Sec VIII, ASME Sec IX, ASME B31.1, ASME B31.3, API1104, AWS D1.1, AWS D1.2, EN 9712, EN1090
Material Type: Depended on client requirement and NDE request.

DEELINE CONSTRUCTION. CO., LTD.
June. 2012 to September 2013
Position: QC Inspector.
Project: GUDRUN PROJECT, OSX3 PROJECT, TROLLA TPCIC PROJECT,
Duties:
- Inspection material such as appearance, dimension received to comply with project
specifications requirements.
- Fit-up inspection, check joint preparation, check dimension to comply with drawing.
- Visual inspection, after weld finish.
- Update status result of fit-up, visual inspection, to database and
- Prepare fit-up and visual report.
- Received NDE request form main contractor and preparation weld joint to NDE inspection.
- Coordinate with team NDE to perform test inspection on site and record result of test to
update status in database.
316,
- Preparation joint RT following with request and coordinate with third party.
- Select joint following with request and coordinate with team PWHT to process.
- Submit progress daily work on site to Supervisor and Main contractor.
- Line check and clearing punch list before leak test.
- Flange management. Check flange face and measurement alignment flange before bolt
torque tightening.
Application code: AWS D.1.1, Norsok, ASME B31.1, ASME B31.3
Material Type: SA516 Gr 70, SA-36 Gr B, SA-572- 50, SA106 Gr B, SA335 Gr P22, P91SA312 TP304, 316

SNT. Mold & Engineering. CO., LTD.
July 2011 to June 2012
Position: Production Engineer
Duties:
- Received work order form client or owner.
- Reviewed drawing form client or owner and prepare draft drawing in program cad-cam.
- Prepare file drawing from cad-cam to program G code device machining.
- Sent to file G code to operator input to CNC machining.
- Planning possesses time of work proper with personal in line manufacturing.
- Planning overtime per day appropriate with personal and job.
- Analysis and solving problems have between possessed manufacturing

สถาบัน TWI Training Thailand

หลักสูตร Welding Inspector CSWIP 3.1

สถาบัน KET. Engineering and Training Center co.,Ltd.

หลักสูตร ASNT TC1A Ultrasonic Testing Level II, ASNT TC1A Magnetic Testing Level II, ASNT TC1A Penetrant Testing Level II,